More pics

Went out to "Der Sweinhaus" to change a tie rod and the gas tank.
.

The paint is totally shot, but in the first pic you can see that there's still some metallic left in the old Polar Silver.

The end of the season

The car is in storage now and I will probably spend more time with the blog, on forums etc.

.

This is how it looks with the narrowed and lowered beam.
NARROWED: 30 mm, slimmed shock towers
LOWERED: unknown amount, 2 x SAW's, about 10 cm drop welded in

.
The rear is going to be lowere about 20 mm next season.

Had some thoughts about slamming it totally, but

I'll do that with my fake split/59 instead. .

The Oval on the left belongs to another

member of "Der Schweinhaus Verein".

Some pics from the trip to BugRun, June 5-7.

Tomorrow it's time to finish the front beam

Haven't had the time to do anyhing for a while. Been choked at work and at home. Was at Bug Run and Hessisch Oldendorf - top event btw. Tomorrow i'll try to get the beam done.

.
Here's some pics of the Oval from way back when ;-)

Ready for MOT-inspection

A new fuel tap, horn and some brake bleeding was all it took. Northern cars rule!

.

Pontus is always ready to help out.

At "Der Schweinhaus"

Drove it to "Der Schweinhaus" to fix the brakes, hand brake, a leaking fuel tap and some minor electric problems.

Time to do some work

Threw out some stuff that came with the car.

Finally

The transport company delivered it to my workplace June 2nd.

I drove it home to do some work on it.

.

Here it is next to the daily driver, an Alfa Romeo 156.

Another month gone by

An old picture is all i can provide.

Didn't do anything this month.
.

More narrowing

The inner part of the shock tower is cut away.

The holes are for spot welding the reinforcement plate and shock towers together.

.

Test fitting the plate.

It's going to be welded to the torsion housing, shock tower and upper shock mount.
.

Test fitting the shock mount.
It's going to be moved 1o-12 mm outwards and shortened by the same amount on the outside. This is to clear the inner fender and make the shock and shock tower line up better.

Narrowing the front beam

These two pics were taken a few weeks ago.

Got an extra front beam that's going to be narrowed about 15mm/side to avoid rubbing the fenders. I'm not after the shopping trolley-look on this one. I think this should be just enough to run 5.1/2 rims with 135x80 15 and clear the fenders.

.

The profiled inner part of the shock tower is cut away to reinforce it internally. The inner part is going to be totally flat, which makes it possible to take away the 15mm/side without modifying the car.

More pictures

Got patina?

Rat look / hood ride rules!

The dashboard

The trip speedo was a nice bonus.

First post

This blog will cover my 57 Oval.

.

It was originally sold in Skövde, Sweden, but ended up 1300 km further north in Övertorneå, where I found it. According to the papers the car was in traffic until April 1976. I don't know why it was taken out of traffic, but the owner had several cars to drive, among others a mid sixties Type 3 Variant.

.

I bought it August 2007 and I will be on the road in May/June 2009. The car appears to be very good condition besides the paint [L324 "Polar Silver"] and some parts of the interior [54 Green]. The paint is really worn but it's going to remain that way. It's hard to beat a dulled out metallic paint where some primer and surface rust shines through. The pan and body apperas solid. No rust basicly, only a few small ones around the rolled fender edges.

.

Didn't have the possibility to do anything with it in 2007 because it was stored too far away. During 2008 I got the original brakes to work and started the engine, mostly see how much work the car needs. Almost everything works, apart from the left brake light and the horn which should be easy to fix. The whole brake system will be replaced - don't like to gamble with a single circuit brake system that's been unused for more than 30 years.